As a factory that has been developing and manufacturing brushless DC motors since 2009, we will break down the different types of BLDC motors for you. After reading this article, you will have a clearer understanding of how to select a suitable BLDC motor for your project, thereby improving the overall stability and efficiency of your equipment.
By Rotor Structure

Inrunner BLDC Motor(Inner Rotor BLDC Motor): The rotor is located inside the stator, which is on the outside. Since the rotor is relatively small, it offers fast dynamic response and rapid acceleration and deceleration. For this reason, internal-rotor brushless DC motors are commonly used in applications that require high-speed motors, such as power tools and high-speed centrifugal pumps.
Outrunner BLDC Motor(Outer Rotor BLDC Motor): The rotor is located on the outside of the stator, which is fixed in place. Since the rotor is larger, it has a higher moment of inertia. Consequently, its rotational speed is slower than that of an inner-rotor motor, but it offers greater operational stability and produces less noise. However, because the stator is located on the inside, heat dissipation relies primarily on the housing, resulting in poorer heat dissipation. At the same power rating, an outer-rotor brushless DC motor delivers higher torque than an inner-rotor brushless DC motor.
By Phase
Single Phase BLDC Motor: Equipped with only one set of stator windings. They feature a simple structure, low cost, and compact size, but suffer from poor starting performance, high vibration and noise levels, and relatively low efficiency. They are suitable for low-power applications such as water pumps, cooling fans, and small household appliances.
Two-Phase BLDC Motor: Equipped with two sets of stator windings with a phase difference of 90°. These motors are relatively rare but operate more smoothly than single-phase brushless DC motors and are primarily used in specific types of cooling fans.
3 Phase BLDC Motor: Features three sets of stator windings with a phase difference of 120° (U, V, W). This is the mainstream configuration for brushless DC motors, offering smooth torque output, high efficiency, and rapid dynamic response. They have a wide range of applications, such as industrial automation, industrial equipment, and high-end devices.
By Voltage
Brushless DC motors operate over a wide voltage range and can meet a variety of power requirements. Based on their rated voltage, they are typically classified into three categories.
Low Voltage Brushless DC Motors (<60 VDC): Safe voltage, compatible with battery voltages, typically used in battery-powered devices or small automated equipment. Examples include scooters, laboratory equipment, battery-powered garden tools, and power tools. Common ratings include 12V, 24V, 36V, 48V, and 60V.
Medium Voltage Brushless DC Motors (60V to 144VDC): Compared to low-voltage brushless motors, these feature lower current, reduced heat generation, and higher efficiency. They are suitable for industrial and mobile equipment, such as electric forklifts and stackers, automated logistics and heavy-duty robots, and industrial and agricultural machinery. Common voltages include: 72V, 96V, 144V.
High Voltage Brushless DC Motors (>144 VDC): Designed for high-power industrial automation equipment, these are commonly used in heavy-duty industrial pumps, heavy-duty electric forklifts, and renewable energy equipment. The typical operating voltage is 310V.
When the power exceeds 7.5 kW, it is recommended to use a voltage of 72 VDC or higher to reduce thermal losses, lower current, minimize heat generation, improve efficiency, and reduce the cost of the driver and cabling.
By Rated Speed
BLDC motors can be classified into three categories based on their rated speed:
Low Speed Brushless DC Motors (<1000 RPM): Low-rpm BLDC motors deliver high stability and torque during low-speed operation. By pairing with different gearboxes(such as planetary, worm, or helical, etc), you can achieve the precise low speeds required for your equipment.
Standard Speed Brushless DC Motors (1000 RPM to 3000 RPM): This is the most versatile speed range in industrial automation equipment, enabling continuous and stable operation.
High Speed Brushless DC Motors (3000 RPM to 50000+ RPM): These motors are typically customized based on your application conditions and power requirements. They demand premium-grade bearings and rotors to withstand extreme centrifugal forces.
By Rated Power
Rated power is a critical parameter when purchasing BLDC motors. Our brushless DC motors, with rated power ranging from 50W to 25kW, can be categorized into the following three types:
Small Power BLDC Motors (<750W/1 HP): These compact, high-efficiency motors are commonly used in space-constrained applications, such as laboratory equipment, small robots, and small conveyor belts.
Medium Power BLDC Motors (750W to 3kW): This power range is commonly used in industrial automation equipment and is suitable for electric scooters, medium-sized AGVs/AMRs, landscaping machinery, industrial pumps, and automated production lines.
High Power Brushless DC Motors (3 kW to 25 kW+): Designed specifically for heavy-duty applications, these motors meet high torque requirements. They often require dedicated cooling systems and are widely used in electric forklifts, heavy-duty stackers, electric vessels, construction machinery, large industrial fans, and salt spreaders.
By Feedback Device
Brushless DC motors employ different feedback mechanisms depending on application requirements:

Sensored Brushless DC Motor: These motors use Hall-effect sensors to detect the rotor position in real time. They offer good value for money but have relatively complex wiring; however, they ensure reliable startup under high torque conditions. They are suitable for equipment requiring heavy-load startup and operation at medium to low speeds.
Sensorless BLDC Motors: These motors estimate rotor position using back-EMF (back electromotive force). Since they lack physical sensor components, they are suitable for harsh environments, high-speed operation with stable loads, and space-constrained equipment.
Brushless DC Motor with Encoder: Utilizing incremental or absolute encoders, these motors provide high-resolution, high-precision position feedback. They are suitable for equipment requiring high-precision positioning, smooth low-speed operation, and high dynamic response.
By Mechanical Structure
Integrated BLDC Motor (built-in driver)
Brushless DC motor with integrated controller offers significant space savings, simplifies wiring, shortens signal transmission paths, and provides strong resistance to interference. However, due to poor internal heat dissipation, it is recommended that the power rating of such motors remain below 750W (1 hp). Additionally, the algorithms in integrated BLDC motors are typically preset and are less flexible than those in external drivers.
They are typically suitable for low-power devices with limited space, such as small automation equipment, robots, AGVs, and AMRs.

Brushless DC frameless motors consist solely of a stator and a rotor. Their flat, compact, hollow design delivers high torque and high efficiency while facilitating easy integration into equipment. These motors are fully customizable, with outer diameters ranging from 30 to 200 millimeters and rated speeds ranging from 1,000 to 10,000 RPM. Ideal for space-constrained applications, they offer high design flexibility. They are commonly used in robotic joints, robotic dogs, and similar applications.

By Gearbox Type
Standard brushless DC motors have a rated torque range of 0.063 Nm to 100 Nm. When your equipment requires a high-torque brushless DC motor, a gear reducer must be used to increase the torque. Depending on the performance and mounting method of the gear reducer, BLDC gear motors can be classified into the following six types.
Parallel Shaft BLDC Gear Motor: The motor’s output shaft is parallel to the main shaft. The overall design is flat or rectangular, making it suitable for equipment with narrow and elongated installation spaces.

Right Angle BLDC Gear Motor: The output shaft is at a 90-degree angle to the motor’s shaft, making it suitable for compact equipment with limited vertical space.
BLDC Planetary Gear Motor: Featuring high efficiency (up to 90% or more in a single stage), high precision, and high power density, they are widely used in precision industrial automation equipment.

BLDC Worm Gear Motor: Featuring 90° right-angle configuration, these motors offer a wide range of single-stage reduction ratios (7.5:1 to 300:1) and feature physical self-locking capability at reduction ratios of 80:1 and higher. However, their efficiency is relatively low, at approximately 60%.

Helical BLDC Gear Motor: As an upgraded version of BLDC spur gear motors, they achieve single-stage efficiencies as high as 95%. Key features include extremely low noise and higher load capacity, making them suitable for equipment with stringent requirements for noise, precision, and reliability. Typical applications include textile machinery, high-power industrial drives, and conveyor systems.

Harmonic Drive BLDC Motor: These motors feature high single-stage reduction ratios, zero backlash, high precision, hollow structure, coaxial output, and high torque density. They are typically used in equipment requiring high precision, compact dimensions, and a lightweight design. Include collaborative robots, humanoid robots, exoskeletons, and semiconductor processing equipment.
Different Types of BLDC Gear Motor Comparison
| Gear Motor Type | BLDC Planetary Gear Motor | BLDC Worm Gear Motor | Helical BLDC Gear Motor | Harmonic Drive BLDC Motor |
| Gear Type | Planetary Gear | Worm Gear | Helical Gear | Harmonic Gear |
| Efficiency | ≥90% | Around 60% | Up to 95% | Typically 70%–90% |
| Advantages | High efficiency, high precision, compact size, high load capacity | Large reduction ratio, compact right-angle structure, self-locking capability at ≥80:1 | Low noise, higher load capacity, smoother operation, and higher durability | Zero backlash, ultra-high precision, compact size, high torque density |
| Limitations | Cost relatively higher | Lower efficiency, higher heat generation | Structure is more complex, cost is higher than spur gear motors | Higher cost, limited overload resistance |
Under complex operating conditions, a single-stage BLDC gearmotor may not fully meet your equipment requirements; we offer multi-stage BLDC geared motor solutions. If you are unsure which type to choose, please contact our professional engineers, and we will select the appropriate one for you based on your specific operating conditions.
By Cooling Method
When operating at high power, under continuous heavy loads, or in high-temperature conditions, brushless DC motors require additional cooling systems to reduce temperature rise, protect the motor, extend its service life, and ensure stable operation.

Water Cooled Brushless DC Motor: Heat is dissipated through a water-cooling or liquid-cooling circulation system. This method offers high cooling efficiency but involves a relatively complex structure. This solution requires external components such as water pumps, resulting in higher costs. However, it operates with relatively low noise and supports fully enclosed operation.
It is suitable for equipment requiring high power density and operating in harsh or fully enclosed environments, such as high-load automated guided vehicles (AGVs), heavy-duty industrial drives, precision equipment, and silent equipment.
Air Cooler BLDC Motor: A fan is mounted at the rear of the motor to provide cooling through forced airflow. With a simple structure and low cost, this is currently the most common cooling method for brushless DC motors. However, heat dissipation efficiency is relatively low; because intake and exhaust vents are required, the system is susceptible to dust contamination and cannot be fully enclosed. Additionally, high-speed fans generate noticeable noise.
It is suitable for conveying equipment, low-voltage industrial fans, and equipment with intermittent loads.
FAQ
What Is the Difference Between Inrunner and Outrunner BLDC Motors?
The main differences between inrunner brushless DC motors and outrunner brushless DC motors are as follows:
- Stator Position: In an inrunner BLDC motor, the rotor is located inside the stator, whereas in an outrunner BLDC motor, the rotor is located outside the stator.
- Speed and Torque: Inner rotor brushless DC motors have higher speeds and lower torque; outer rotor brushless DC motors are the opposite.
- Heat Dissipation: Due to the shorter heat dissipation path, internal rotor brushless DC motors offer higher heat dissipation efficiency.
- Applications: Inrunner brushless DC motors are suitable for high-speed, high-power applications. Outrunner brushless DC motors are suitable for low-speed, high-torque applications.
Are All BLDC Motors Three-Phase?
No, not all BLDC motors are three-phase. Three-phase BLDC motors are the most common type of brushless DC motor. In addition to three-phase models, single-phase and two-phase options are also available.
What Is the Advantage of an Integrated BLDC Motor Over an External Driver?
Compared to BLDC motors with external drivers, integrated BLDC motors offer a more compact overall design, saving installation space, simplifying wiring and commissioning, reducing electromagnetic interference, and providing better system integration.
Conclusion
There is a wide variety of brushless DC motors available on the market. If you are unsure which motor is right for your project, please contact our professional engineers. They will help you select the appropriate model or customize a brushless DC motor that is 100% compatible with your equipment.




